Must Have Tools for Homeowners | Power Tools Every Homeowner Should Have

      Comments Off on Must Have Tools for Homeowners | Power Tools Every Homeowner Should Have
  1. Brad Nailer

When using a brad nailer tool, you will need the following items.

  • A Brad Nailer
  • Hose adaptor
  • An air compressor
  • Air hose
  • Teflon tape
  • Pneumatic tool oil
  • Adjustable wrench
  • Tack cloth

A brad nailer is normally a hand held tool which is used to fore brad nails. They are finishing nails that are at one side of the head. There are various types of brad nails that do not have heads. They also vary in size from half an inch to two inches.in order to hammer those nails into wood you need a brad nailer. There are two types of brad nailer a pneumatic and electric one. The pneumatic tool needs to use an air compressor in order for it to shoot brad nails.

Here is a step by step guide on how to use a brad nailer.

First you need to get the correct type of a hose adaptor which will be able to fit the brad nailer. You will also need to buy a Teflon tape and a pneumatic tool oil. The purpose of the Teflon tape is to help hold the hose and the device to avoid being loose.

The second thing is wrapping the connector with Teflon tape. Ensure you wrap the fitting onto the hose adaptor using the Teflon tape. Using the adjustable wrench, tighten the connection more so that air does not leak out.

The third step is to lubricate the brad nailer, it uses an air piston for it to work, and hence it should be lubricated so that it can work efficiently. Use the pneumatic tool oil to lubricate the device. Using the tack cloth, clean the mess created.

Step four is loading the brad nailer with nails, load the amount of nails required for your project, each brad nailer model uses different amounts of nails.

The other step is to connect the brad nailer to an air compressor, allowing the air compressor to pressurize before connecting the brad nailer tool winner. Ensure you connect one end onto the end of the hose to the air compressor and the other end onto the brad nailer. Make sure the connections are tight enough.

The sixth and final step is to test the device, using a piece of wood, hold the handle and place it into position. The tip of the brad nailer should rest on the wood at a 90 degrees angle. Pull the trigger and let the brad nail to sink into the wood, if it works correctly, then it is ready for use.

  1. Plasma Cutter Cart

Do you always find yourself stopping every now and then move your plasma cutter then readjust it once again? Then a plasma cutter cart will come in handy for you. It helps you enjoy your welding experience and ensures that you are safe when working on your various projects.it does not matter if you are an amateur or a professional welder, the cart comes in handy for every single person using the plasma cutter, and it is worth every coin of your money.

The cart is installed with wheels, compartments which is very helpful in keeping all your equipment close to you when working for easier reach. There are various that manufacture carts and it will totally depend on your individual preference since there are many varieties to choose from the market.it is no secret that the plasma machines are quite heavy and difficult to move around. Good carts include a section for placing your gas tanks.

  1. Table Saw

A table saw is tool for wood working which has a circular saw blade that is mounted on an arbor which is driven by an electric motor, either by belts or gears. The blade normally protrudes through the surface of a table that gives support for the wood that is being cut. The latest table saws have varied depth of the cut, whereby, when the blade is higher above the table the cut becomes deeper. There are various types of table saws, these are the benchtop table saws, the contractor table saws, the cabinet table saws as well as the hybrid table saws.

  1. Mower

When using a mower, the first thing is to ensure that you prepare to start the lawn mower, move it to an open area. Clear all things that might come on the mower’s way.

Second, ensure that your mower has enough gas as well as oil. If your mower is the type that has a 4-stroke engine you can be able to check the amount of oil by opening the oil fil cap or the dipstick. If it is a two stroke you will have to mix the oil in the gas. It is important that you make sure to mix the right kind of oil with the gas in a correct ratio as well.

The third step of using a mower is to check the spark plug, there is supposed to be a single spark plug end that is sticking out of the motor, and a rubber cap that is attached to it.When it is attached well the appearance will be like a thick rubber hose that is capped on a metal protrusion. If you find out that the spark plug is not firmly held, you should look up on the user manual as well as get it checked by a mechanic in order to fix it.Also have your mechanic to change the spark plug once a year.

Next you should prime the carburetor, locate the prime bottom usually black or red squishy button on the mower’s body. Push the button up to 4 times for it force the gasoline into the lines, butdo not press too much or else you will flood the engine, always refer to user manual if you cannot find the prime button. Skip this step if your mower does not have a prime button.

Next step is to open the throttle, this normally used as a lever on the handle of the mower or the engine body. Ensure that you put the throttle on a mid to high position, in case you skip this step the engine will not keep going after you have started it.

In case the mower is cold, ensure that you set the choke, which helps in providing a richer fuel air mixture to the engine, which therefore helps it to stay running until it warms up. After the mower runs for a few minutes ensure that you turn the choke off.

The final step of operating a mower is to pull the starter cord, if your mower has a horizontal lever near the handle, ensure you hold it against the handle, then grip the handle of the started and pull upwards in a fast manner and firmly. You might have to repeat this several types for the mower to start up.

If it does not start up the spark plug may not be attacked, fix it then try to start your mower again. Sometimes it may not start if you do not have enough gas in the tank.

 

Timothy Corrigan

The award-winning interior designer Timothy Corrigan is an American Interior designer. He was featured as the world most 100 Interior Designer and blogger in 2009. He got the prestigious award ‘Star of Design’ and ‘2017 Design Icon’. According to the Robb Report’s, he was placed at the top 40 Interior Designer. Many prestigious publications featured Corrigan as an interior author and designer such as ‘The Times’, ‘Architectural Digest’, ‘The New York Times’, ‘BuyingNote’ and so on. He is the featured author of BuyingNote. He shares his valuable opinion and suggestions to our readers about the home design and household necessities. Corrigan is the specialist of home décor and household necessities.

About Timothy Corrigan

The award-winning interior designer Timothy Corrigan is an American Interior designer. He was featured as the world most 100 Interior Designer and blogger in 2009. He got the prestigious award ‘Star of Design’ and ‘2017 Design Icon’. According to the Robb Report’s, he was placed at the top 40 Interior Designer. Many prestigious publications featured Corrigan as an interior author and designer such as ‘The Times’, ‘Architectural Digest’, ‘The New York Times’, ‘BuyingNote’ and so on. He is the featured author of BuyingNote. He shares his valuable opinion and suggestions to our readers about the home design and household necessities. Corrigan is the specialist of home décor and household necessities.